go to the gnb menu go to the content

FAQ

ホームお客様サポートお問い合わせFAQ

Component

Camera Module

Substrate

  • MLCC (Class II) product has the characteristic that capacitance is decreased when DC voltage is applied, This could be measured using the typical LCR meter. 

     

    - Measurement equipment : LCR meter E4980A + Test Fixture 16034G/E (Keysight Technologies Corp.)

     


     

    - Test conditions

    1) Frequency : refer to SPEC sheet for each product (e.g., 1kHz, 120Hz)

    2) AC voltage: refer to SPEC sheet for each product (e.g., 1Vrms, 0.5Vrms)

    3) DC voltage : from 0Vdc to Rated voltage, keep time(60sec) by each point

    4) ambient temperature  : 25℃ ± 3 ℃

     

    ※ Caution

    1) Measurement should be proceeded after ‘pre-treatment at 150℃ for 1hour and keep at room temperature for 24hour’

    　 *refer to FAQ “MLCC Aging phenomenon”

     

    2) Because the voltage source of LCR meter has internal resistor, the voltage between DUT terminals may differ from setting voltage. This equipment(E4980A) provides ALC(Auto level control) function to control DUT voltage. Therefore, capacitance should be measured while ALC function is activated. If ALC function is not activated, the capacitance value may be a little low. (Figure a, b, c, d)

     

    3) Since parasitic of the  test fixture can affect on capacitance value, Short status and Open status of fixture and cable length must be properly corrected. (figure e, f)

     

    Please refer to the user guide of the equipment for detailed measurement setting methods.

     


     

    [Reference]

    - Impedance Measurement Handbook, Keysight Technologies Corp. 6th Edition, 2020

  • The BGA production base is the domestic Sejong Plant, and the FCBGA products are produced at the domestic Busan Plant and the overseas Vietnamese production base.

  • FCBGA is used in a variety of fields from PC and game device to Data Center and automobiles, etc.

    - Client: CPU and GPU for Desktop and Note PC, SoC for Game Console

    - HPC: CPU for Server, ASIC for AI accelerator

    - Network: ASIC for Router/Switch

    - Automotive: SoC for ADAS, Radar and Infotainment

  • When you go to the Contact us on the main page or the Product page, you can ask questions about technologies and purchases by each region.  

  • 1) Searches can be done through Samsung Electro-Mechanics’ website > Product Search.

    2) Product searches can also be done through the Google search window. Input passive component P/N in the search window > Click on the ‘Samsung Electro-Mechanics : Product Information’ from among the search results > Relevant product page opened 

  • If the product you want has been discontinued, our website allows you to search for substitute products. For example, if you’re looking for a substitute for CL10A106MP8NNNC with the same size and capacity, you can follow these steps.

     

    1)First, you need to understand the Part Numbering System rules. If you don’t remember, click the question mark icon on the Product Search menu, and an information window about the Part Numbering System will pop up.

    2)The numeric values included in a Part Number indicate certain attributes.

     

     

     

    Size is indicated by the third and fourth digits in the number. '10' corresponds to 0603(1608), which means 1.6 mm × 0.8 mm. Capacity is indicated by the sixth through eighth digits. '106' means 6th power of 10×10; that is, 10,000,000 pF = 10.㎌.

     

     

    With the spec. information you gave, it is difficult to share the exact part.(need size tol and additional info.)

    I recommend you to use our web library.

    If you use our library below, you can select the model you want to check the electrical performance.

     

    http://weblib.samsungsem.com 

  • 1) Go to “Product Search,” and click on the tab for the product you want.

    2) Enter the Part Number (e.g., CLL5Z105MS3NLNH) to begin the search.

    3) When the search results are displayed, check the “Status” section to see if the product is in “Mass Production” or “Under Development.” In most cases, products not included in the search results are “Discontinued Products.” However, there are some products that are not displayed for other reasons. It would be a good idea to contact our staff to see if it has been discontinued.

     

    Request : http://www.samsungsem.com/global/support/contact-us/inquiry.do 

  • There is no specification for allowable current of MLCC.
    When DC voltage is applied into MLCC, there is no issue since almost no current flows through the MLCC, however, when the AC voltage or pulse voltage is applied, the current flows through the electrode which leads to generate heat. Therefore, check the self-heating temperature by input AC or pulse voltage when the capacitor is used.

     

    2-6. Self-heating Temperature ( in Datasheet)
    It is necessary to design the system, with considering self-heating generated by the ESR (Equivalent Series Resistance) of MLCC when AC voltage or pulse voltage is applied to MLCC.
    2-6-1. When MLCC is used in an AC voltage or pulse voltage circuit, self-heating is generated when AC or pulse current flows through MLCC. Short-circuit may be occurred by the degradation of MLCC’s insulating properties.
    2-6-2. The reliability of MLCC may be affected by MLCC being used in an AC voltage or pulse voltage circuit, even the AC voltage or the pulse voltage is within the range of rated voltage.
      Therefore, make sure to check the following conditions.
    1) The surface temperature of MLCC must stay within the maximum operating temperature after AC or Pulse voltage is applied.
    2) The rise in increase by self-heating of MLCC must not exceed 20℃

     

  • The insulation resistance is the resistance of dielectric material of MLCC. The insulation resistance value is calculated by dividing the rated voltage by the leakage current, and the leakage current is the current flows both electrodes when the rated voltage is applied. Insulation resistance is generally MΩ values, and when the voltage is applied., as shown in the picture, First, current is charged both electrode of MLCC, and therefore, insulation resistance is measured 60 seconds after the voltage is applied.

     

  • The capacitance value of MLCC is determined by the number of dipoles in the dielectric that are aligned at both ends of the electrode when voltage is applied as shown in the figure below. When AC voltage is applied, the capacitance value increases in proportion to the number of dipoles that move (align) according to the AC voltage. the meaning of capacitance is C=Q/V, which represents the amount of electric charge accumulated on the electrode when a voltage is applied to the MLCC.

     


    In the case of C0G, a Class 1 type, there is no change in capacitance even when DC voltage is applied.
    However, in the case of Class 2 (X5R, X7R, etc.) type, the capacitance gradually decreases as the DC voltage increases as shown below.
    The reason is that when a DC voltage is applied, the dipoles in the dielectric are aligned and fixed according to the direction in which the voltage is applied, thereby reducing the number of dipoles that move to voltage changes (AC voltage) It is proportional to the number of dipoles reacting to AC voltage.) As the applied DC voltage increases, the number of dipoles aligned and fixed increases.
    As a result, as the number of dipoles for implementation of capacitance decreases, the capacitance value gradually decreases.

     

first 1 2 3 4 5 6 7 8 last

もっと知りたい場合、「質問する」を通してご質問して下されば誠実にお答え致します。

今すぐ質問する
Online Museum TOP
ニュースレターを購読しますと、サムスン電機の最新ニュースをお届けします。

世界最高のトータル部品メーカであるサムスン電機の
生々しいニュースをお伝えします。

  • ニュースレターお申し込み用個人情報収集、ご利用同意 (広告・宣伝情報の受信に同意) 内容を見る

    1. Purpose of Collecting Personal Information

    Samsung Electro-Mechanics Co., Ltd. (hereinafter referred to as "SEM") collect your email information to deliver reports or news published by SEM, and the collected personal information will not be used for any purpose other than the specified purpose, and in the event of any change in the purpose of the collection, you will be notified in advance for your consent.

    2. Terms of Retention and Usage of Personal Information

    When you apply to unsubscribe from the newsletter, your personal data will be destroyed without delay. If the retention of the information is required by other laws, personal information for which the term of retention and use has expired may be retained without being destroyed.

    3. Personal Information We Collect
    • Item(s) : Email
    • Period of Retention : Until request of unsubscribe to newsletters
    • Purpose of Collection : To provide reports and news from Samsung Electro-Mechanics
    • Information Automatically Collected : IP(Internet Protocol), Cookies, Access log
    4. Matters Concerning the Consignment of Personal Information Processing

    The “sending of newsletters” is entrusted to and operated by an external professional company as shown below to perform the service. In accordance with related laws, such as the Personal Information Protection Act, the Company specifies in its agreement with the external service provider matters concerning the liabilities, such as the prohibition to use personal information for purposes other than those to perform the consigned service, technical and administrative protective measures, restrictions on re-consignment, management and supervision of the trustee, damages, etc., pursuant to related laws such as the Personal Information Protection Act, and SEM will notify you without delay in the event of any change in the details of the consignment or any change of the consignee.

    Matters Concerning the Consignment of Personal Information Processing
    Name of the Consignee Company The Uber Creative
    Representative Telephone Number +82-2-517-5133
    Consigned Work Sending out newsletters, operation and maintenance of the website

    ※ You have the right to refuse to consent to the collection and use of your personal data, and if you do not agree, you will not be able to receive the newsletter.

    I have read the above contents and agree to the collection and use of my personal information including consent to receive advertising information.

  • サムスン電機ニュースレターの受信に同意します。

ニュースレターお申し込み